Can You Put Two Blades On A Table Saw?

By / Saw

For sawing thicker metal pieces, it’s sometimes tough to get the work done through a single saw blade.

So, can you put two blades on a table saw? This becomes a common question among those who are quite new.

Today, I’ll explain why and how you can smoothly put double blades on your power tool; read on…

Should You Use 2 Blades In A Table Saw?

Should You Use 2 Blades in A Table Saw

Yes. In fact, many carpenters these days prefer using double blades in a table saw. This way, they don’t need to change the blade frequently to cut up heavy metals.

Plus, the task becomes less complicated. But you’ll need to confirm that the teeth of those two blades aren’t getting into contact with each other.

Also, make sure the diameter of those two blades is 100% equal. If not, they will mismatch, and you’ll end up getting negative feedback.

How to Effectively Put Two Saw Blades Together In a Table Saw: Step By-Step Guideline

To be honest, there is not much information online about how to put two saw blades together in a table saw. Considering this fact, I’m going to share every detail possible through this step-by-step guide:

Tools Needed

Step-1: Switching Of the Power

For safety purposes, it’s always better to unplug the table saw to switch off your power tool completely. Let it sit for a while, ensuring that every power drains from your table saw. 

Step-2: Taking Off Blade Plates & Blades

In order to put two saw blades, you must remove the blade plate thoroughly. Usually, you’ll find them well-secured with no less than 2 screws: one in the rear part and the other one in the front. With the assistance of a screwdriver, carefully loosen them to take off the plate.

After that, keep that aside for the next step. Here, you need to remove the blade.

For this, take off the washer and nut from the blade as safely as possible. And don’t forget to turn them anticlockwise using a piece of Hex wrench.

Step-3: Incorporating Two Blades

Let’s set up those blades you’ve collected onto that housing of blade. Afterward, you must position the nut and washer in place, securing them through tightening and turning clockwise.

Finally, using a block of wood, make sure to hold each blade safely.

Once you’ve added two blades to your table, saw, get your hands on a screwdriver in terms of reinstalling the plates. For this, all you need is to tighten each screw that was used to settle those plates.

Step-4: Have a Check

Right now, you can plug your table saw back into any wall socket, ensuring each blade is moving in the right direction.

If you notice that both of these blades are moving in the same manner, then pat yourself on the back as you’ve done it successfully!

What Is The Advantage Of Using Two Table Saw Blades Together? 

Here, I’ve listed down a couple of benefits behind using dual blades together on your table saw –

  • The most prominent advantage of using two blades together is that you’ll become able to make almost every cut at once, including crosscuts, backward cuts, forward cuts, or downward cuts. 
  • The possibility of ending up with a kickback gets lower than usual.
  • Unlike the sick-blade table saw blade, double blades offer more strength, power, and even better control. 
  • For ensuring smooth and sharp edges, two blades really come in handy
  • Last but not least, the heavy metal-cutting task turns a piece of cake if you choose two blades instead of one. 

Tips And Safety Requirements For Using Two Table Saw Blades Together

No chance to think that operating two blades together is child’s play. Here, you need to follow some experts’ advice and safety tips, which is what I’m going to show you now –

  • While operating double blades, avoid putting on safety gloves to get more gripping strength. Instead of that, wear a face mask, goggles, and short sleeves to stay risk-free.
  • Following the users’ guide is crucial while installing table saw blades. Why? Because nowadays, there are some unique and new saw blades available, which require a different installation process.
  • Avoid two blades if you’re going to perform light projects. It doesn’t make sense to spend a fortune on dual blades to complete some easy-peasy woodworking tasks!
  • You must disconnect the power before you start installing blades, eliminating major injuries.
  • Look for additional screws, stones, or nails before you start your table saw. Otherwise, those blades may contact them and end up with cracks.

What Type Of Projects Does Need 2 Table Saw Blades?

The answer will be straightforward; the project that requires heavy strength, power, and durability will require 2 tables saw blades.

Besides, if you want to make crosscuts, ripping cuts, and backward cuts together, a single saw blade mightn’t be efficient every time.

Is It Difficult to Use 2 Table Saw Blades At a Time?

It depends on your level of experience. The installation process of 2 tables saw blades might be a little trickier than the single blade.

But when it comes to operating them, I don’t think it’s going to be a back-breaking task. 

That said, if you’re very new in the field of sawing, then never try to use two blades together to avoid imperfections and risks; keep in mind!

Frequently Asked Questions (F.A.Q):

What are the dado blades in table saws used for?

Compared to traditional blades, dado blades appear to be relatively wider and used for interlocking tasks, including making bookshelves, door panels, drawers, cabinets, etc.

What is the best table saw blade for cutting hardwood?

Actually, there are numerous choices available when it comes to the best table saw blade for cutting hardwood. Among them, I’ve found the rip blade more ideal for being hardwood-friendly.

Last Words!

From now on, if anybody asks, can you put two blades on a table saw, then show them what you’ve learned through this article?

In order to make the best use of dual blades, always follow the safety requirements and the installation guide I’ve mentioned above. That’s enough!

Our Related Saw Blade Article

Leave a Comment

Scroll to Top